|
[Home] [E-Mail]
[Seating
Barriers] [Moisture
Barriers] [Panel
Barrier]
[Cal-133
Q&A] [Cal-133
The Law] [Cal-133
Test Info.] [Cal-133
Test Labs] [States
w/Cal-133] [Laminators]
[Links]
FIREGARD
European Fire Standards
info@intekfiregard.com
Flammability testing is arguably one of the most important testing
procedures within the textile industry because it has crucial safety
implications in the event of a fire. It has been statistically shown
that the major cause of fatalities in fire can be directly attributed
to the accidental ignition of upholstery and textiles, so it is only
sensible that proper flammability standards should be in place. Flammability
performance can be improved by the fabric manufacturer at the design
stage to ensure a safer interior environment.
Unfortunately, there is no single flammability standard for upholstery or
vertical surface fabrics which has been adopted as the norm throughout the
world and the plethora of different standards in force internationally
reflects the different ways of approaching the whole flammability issue. A
single standard has been brought in which is acceptable throughout the
European Union, EN 1021 : 1994, but this only covers cigarette and match tests
- nothing more rigorous - and other national tests continue to proliferate.
This guide looks at some of the most important international standards and
test methods which apply to upholstery fabrics. Sadly, it can never be a
definitive document, but should hopefully provide a better insight into the
main regional variations and the complex issue that flammability testing has
become.
European standards
EN 1021 - 1/2 : 1994
This standard is valid throughout the EU and examines a fabric's reaction to
a burning cigarette and butane flame (simulated match). It replaces a number
of national tests, including DIN 54342 : 1/2 in Germany and BS 5852 : 1990 in
the UK.
Test Methods
A standard test rig is constructed from fabric and foam to form a simulated
chair with the back at a right angle to the base. This enables the ignition
source to be kept in permanent contact with both back and seat throughout the
test. Watersoak prior to testing is compulsary.
EN 1021 : Part 1
In Part 1 of the test a lighted cigarette is placed in the angle of the
test rig and left to smoulder along its entire length. After 60 minutes no
smouldering or flaming of the fabric should be observed.
EN 1021 : Part 2
Here a butane flame 35mm in height is used to represent a burning match and
is applied for 15 seconds, again in the angle between the test rig base and
back. After the flame is removed, no burning of the fabric should occur after
2 minutes have elapsed.
Germany
In Germany, upholstery fabrics are tested in accordance with DIN 4102 which
has been established by the Deutsches Institut fŸr Bautechnik.
DIN 4102 Part 1 - Kleinbrenner (B2)
All materials used in buildings in Germany need to meet the B2 requirement
which is determined using a small flame test.
The fabric specimen is suspended vertically and a 20mm high flame is
applied for 15 seconds to both the fabric surface and edge. Reference lines
are marked on the specimen, which achieves B2 classification if the tip of
the flame does not reach the reference marks within 20 seconds on any sample.
5 samples are tested with filter paper being placed below each to determine
the production of flaming droplets.
DIN 4102 Parts 15/16 - Brandschacht (B1)
Referred to as the "Brandschacht test", this is the main test
method in Germany which measures reaction to fire and is considered the
highest flammability standard in the country for upholstery fabrics.
The term Brandschacht, literally "fire shaft", refers to the
testing apparatus itself which consists of a square-shaped vertical housing
equipped with a gas burner. Four fabric samples are held vertically in a
supporting frame and subjected to flames for 10 minutes. At the same time a
constant, uniform flow of air is blown into the Brandschacht from below.
In evaluating the test, smoke gas temperature and the mean residual length
of the sample are taken into account (residual length is the part of the
specimen which has escaped burning). In order to be classified as B1, the
tested fabric must show:
1. A mean residual length of not less than 150mm, with no specimen being
burned away completely
2. A mean smoke gas temperature of less than 200oC
France
NFP 92 - 503 - Bržleur ƒlectrique
The French test known as the "Bržleur ƒlectrique" - electric burner
- is the principal method used not only in France, but also in Belgium, Spain
and Portugal. It results in a classification of M1 to M4, with M1 being the
highest classification.
The sample is placed face down on the test rig at an angle of 30o above an
electric radiator which gives out heat. A small butane gas pilot flame is
applied directly to the fabric surface at 20 seconds into the test, held in
position for 5 seconds then withdrawn. The flame is applied again at 45
seconds and subsequently every 30 seconds for the duration of the 5 minute
test. If any flaming continues after 5 minutes, the test is continued until
the specimen extinguishes completely.
The following aspects are noted during the test:-
- duration of flaming
- production of burning droplets
- length/width of the damaged specimen
Actual classification requirements are given below:-
|
Classification
|
|
M1
|
M2
|
M3
|
>M3
|
|
Duration of Combustion
|
s
|
<=5
|
>5
|
>5
|
>5
|
|
Damaged
|
Length
|
mm
|
-
|
<350
|
<600
|
600
|
|
Width
|
mm
|
-
|
-
|
<90
|
>90
|
|
Droplets
|
|
none
|
none
|
none
|
|
NFP 92-504 - Rate of flame spread test
This complimentary test to the Electric Burner helps establish a
classification on samples which behave unusually during the primary test -
for example, melting rapidly or shrinking away to form a hole so that the
pilot flame cannot come into contact with the sample at 20 seconds, or if
samples were unable to achieve an M3 rating.
For materials which melt or shrink away from the heat source, after flame,
non-propagation of flame and burning/non burning droplets are observed. Rate
of flame spread is also measured if the material does not achieve M3.
The non-propagation of flame test involves a flame being held against the
free end of a horizontal sample, 10 times for 5 seconds; the time of after
flame is measured.
In the flame spread test, the time taken for flame to spread between two
reference marks at 50mm and 300mm is established. The production of burning
droplets is also noted.
Classification criteria are given below:-
|
Classification
|
M1
|
M2
|
M3 a
|
M3 b
|
M4
|
|
Duration of Combustion
|
none
|
<5s
|
<5s
|
>5s
|
>5s
|
|
Droplets
|
None or non burning
|
None or non burning
|
Burning
|
None or non burning
|
Burning
|
NFP 92-505 - Dripping test
Again complimentary to the electric burner, the dripping test is employed to
investigate further into the potential hazard of burning droplets observed
during the primary test.
A sample is placed on a grid 30mm below a radiator and a receptacle
containing cotton wool is positioned 300mm below the grid. Heat is applied
from the radiator for 10 minutes and the test is repeated 4 times. If the
cotton wool sets alight, the fabric is classified M4. If it does not ignite,
even if flaming or molten drips are produced from the sample, the original
classification from the electric burner test is retained.
United Kingdom
BS 5852 : 1990
This defines the actual test method whereby a specially constructed test rig
is designed to form a simulated chair, as described in EN 1021. The foam used
is not specified.
Of the eight ignition sources, the most frequently used are Ignition
Source 0 (cigarette), Ignition Source 1 (butane flame/simulated match) and
Ignition Source 5 (Crib 5). Moving up the ignition source scale, the heat
intensity roughly doubles as compared to that of its predecessor.
The requirements for the cigarette and match tests are the same as those
detailed under EN 1021, although the match application time was previously 20
seconds before the European Norm was introduced.
The Ignition Source 5 test is more rigorous due to the increased intensity
of heat which is generated from the wooden crib structure. Alcohol is added
to the small piece of lint at the bottom of the crib which is then placed on
the test rig and ignited within 2 minutes. For a pass to be recorded, all
flaming should cease within 10 minutes.
BS 7176 : 1995
BS 7176 is a performance standard based on BS 5852, but with three
additional parameters:-
(i) Watersoak procedure
(ii) Predictive "Worst Case" testing
(iii) Hazard categories
Watersoak
This procedure is defined precisely in BS 5651 : 1990 Clause 3, but in simple
terms requires that a fabric be soaked in water and dried prior to testing.
This is done because chemically treated material may be adversely affected by
watersoaking and its additional flame retardant characteristics may be
greatly reduced or completely eliminated.
Predictive worst case testing
Here the foam used on the test rig is 35kg/m3 High Resilient (HR) foam (not
CMHR foam). This has been adopted as a 'worst case' foam on the assumption
that the vast majority of manufacturers use Combustion Modified foam which
gives better flammability performance.
Hazard Categories
BS 7176 also helps to identify varying 'hazard' categories which are linked
directly to the ignition source used for testing. There are four categories:-
|
|
Low Hazard
|
Medium Hazard
|
High Hazard
|
Very High Hazard
|
|
Typical Examples of usage
|
Offices,
Colleges,
Museums,
Exhibitions,
Day Centres,
Schools
|
Hotel Bedrooms
Public Buildings
Restaurants
Services Messes
Places of Public entertainment
Public Halls
Public Houses
Bars and Casinos
Hospitals
Hostels
|
Sleeping accomodation in certain hospital wards and in certain hostels.
Offshore installations
|
Prison cells
|
|
1. If a particular premise in the Low Hazard area is used for sleeping
purposes then consideration should be given to specifying a higher
performance level.
2. Upholstered furniture which is ordinarily intended for private use in
a dwelling is subject to Government Regulations.
|
Typical examples of end usage are indicated by BS 7176 so that the user
(and fire officer) knows what specification of fabric is required where.
Classifications cover low, medium, high and very high hazard categories with offices
coming in the lowest risk category and public buildings, hotels, restaurants,
etc being labelled medium hazard. However, it is important to note that these
are guidelines only and fire officers and specifiers alike can demand higher
standards; this is often true of office environments where "Medium
Hazard" fabrics are increasingly preferred.
BS 476: Part 7 (1997)
This standard assesses the flammability performance of flat materials,
composites or assemblies, which are used as the exposed surfaces of walls or
ceilings. Hence this is the standard which is applied to vertical surface or
panel fabrics. The spread of flame along the surface of a specimen held in a
vertical position is determined and the subsequent classification system is
based on the rate and extent of flame spread.
The test equipment consists of a vertically mounted radiation panel,
supplied with a gas-air mixture, together with a specimen holder and pilot
flame arrangement mounted to one side. The specimen holder swivels so that it
is located at 90o to the face of the radiation panel during the test.
The fabric sample is exposed to the radiation panel for 10 minutes (or
until the flame has reached a reference line drawn at 825mm - whichever
occurs first) and for the first minute a pilot flame is applied to the bottom
corner of the sample. During the test, the time taken for the flame to reach
various reference marks is noted, along with the extent of flame spread at
1.5 minutes and at the end of the test. A minimum of six and a maximum of
nine samples are tested and are classified according to the performance
results shown in the table below.
|
Classification of spread of flame
|
|
Classification
|
Spread of flame at 1.5 min.
|
Final spread of flame
|
|
|
Limit (mm)
|
Limit for one specimen in sample (mm)
|
Limit (mm)
|
Limit for one specimen in sample (mm)
|
|
Class 1
|
165
|
165+25
|
165
|
165+25
|
|
Class 2
|
215
|
215+25
|
455
|
455+45
|
|
Class 3
|
265
|
265+25
|
710
|
710+75
|
|
Class 4
|
Exeeding the limits for class 3
|
Vertical Surface Test
The Vertical Surface Test has been specifically devised by Interface Fabrics to
assess the flame retardancy of panel systems in typical installation
conditions. It has not been formally adopted under national or international
legislation, but is the test we are seeking to promote and advocate as being
better indicative of how a panel structure is likely to react in a fire.
Test Method
The test utilises the standard test rig and ignition sources as per EN 1021
which is the standard for upholstered furniture. An "L" shaped
construction in this instance simulates a panel in direct contact with its
base.
For testing purposes a typical panel construction consists of a soft wood
frame with plywood frontage covered in 2mm HR foam. The panel fabric to be
tested is then clipped around the panel and positioned the test rig. The base
is constructed of chipboard covered in laminate to simulate a desk top. The
vertical surface test also includes a watersoak procedure for the fabric.
Ignition Sources
The ignition sources used and the length of time for which they are applied
are identical to those for testing upholstered furniture, ie. Ignition Source
0 (cigarette), Ignition Source 1 (match). The pass criteria are also the
same.
Italy
Numerous building laws and regulations exist in Italy relating to fire
protection. "Circolare No.12" of the Ministry of the Interior
contains test procedures enabling the flammability performance of building
materials - including fabrics - to be established and classified. To achieve
an overall classification, the small burner ignitability test (CSE RF 1/75 A
or CSE RF 2/75 A) must be conducted together with the surface spread of flame
test (CSE RF 3/77). The results of both tests are then used to determine an
overall classification, from Class 1 to Class 5 - Class 1 being the best.
CSE = Centro Studi ed Esperienze (Research Centre of the Ministry
of the Interior)
RF = Reazione al fuoco (Reaction to fire)
CSE RF 1/75 A, CSE RF 2/75 A
These small burner tests roughly correspond to the German Kleinbreiner test
(DIN 4102 Part 1) except for the size of specimen and the absence of filter
paper to check for burning droplets.
CSE RF 1/75 A is an edge application flame test, with the flame applied
for 12 seconds, while CSE RF 2/75 A uses surface application of the small
flame for 30 seconds. In both tests, after flame time, afterglow time, extent
of damage and flaming droplets are observed and recorded. These parameters
are then divided into three grades, as shown in the table below:
|
Grade
|
Afterflame time (s)
|
Afterflame time (s)
|
Extent of damage (mm)
|
Time for drippings to extinguish (s)
|
|
1
2
3
|
<5
>5 - <60
>60
|
<10
>10 - <60
>60
|
<150
>150 - <200
>200
|
non burning
<3
>3
|
The grades of the four parameters are then multiplied by "weighting
factors" in order to establish the category into which a product falls,
which then serves as the basis for assigning a classification to a product.
|
Parameter
|
Weighting Factor
|
|
After flame time
After glow time
Extent of damage
Dripping
|
2
1
2
1
|
|
Category
|
Weighted sum of grades (grade x weighting)
|
|
i
ii
iii
iv
|
6 - 8
9 - 12
13 - 15
16 - 18
|
CSE RF 3/77
In the spread of flame test, the sample is exposed to a small pilot flame and
radiant panel. The position of the test specimen is varied to simulate end
use in floors, walls and ceilings. Parameters measured are the rate of spread
of flame, extent of damage, afterglow and flaming droplets, which again are
divided into three grades. The category on which classification is based is
then worked out by multiplying the different grades with various weighting
factors, which for flaming droplets are distinguished between floor, wall and
ceiling use.
|
Grade
|
Rate of spread of flame (mm/min)
|
Extent of damage maximum length
|
Afterglow time (s)
|
Time for drippings to extinguish (s)
|
|
1
2
3
|
not measurable
=<30
>30
|
=<300
=>300 - =<600
>600
|
=<180
=>180 - =<360
>360
|
not burning
=<3
>3
|
|
Parameter
|
Weighting factor
|
|
Rate of spread of flame
|
2
|
|
Extent of damage
|
2
|
|
Afterglow
|
1
|
|
Dripping
|
floor
|
0
|
|
wall
|
1
|
|
ceiling
|
2
|
|
Category
|
Weighted sum of grades (grade x weighting)
|
|
Floor
|
Wall
|
Ceiling
|
|
i
|
5 - 7
|
6 - 8
|
7 - 9
|
|
ii
|
8 - 10
|
9 - 12
|
10 - 13
|
|
iii
|
11 - 13
|
13 - 15
|
14 - 17
|
|
iv
|
14 - 15
|
16 - 18
|
18 - 21
|
Classification
The categories obtained from the different tests form the basis for
classifying products, as follows;- For classification in classes 2, 3 and 4
respectively, two, five and seven combinations of categories obtained are
available.
|
Test Method
|
Conditions
|
Class
|
|
method CSE RF
|
Compliance with categories to choice
|
|
|
1/75/A or 2/75/A
3/77
|
i
i
|
|
|
|
|
|
|
1
|
|
1/75/A or 2/75/A
3/77
|
ii
i
|
i
ii
|
|
|
|
|
|
2
|
|
1/75/A or 2/75/A
3/77
|
iii
ii
|
ii
iii
|
i
iii
|
iii
i
|
ii
ii
|
|
|
3
|
|
1/75/A or 2/75/A
3/77
|
iv
iii
|
iii
iv
|
iii
iii
|
iv
ii
|
ii
iv
|
iv
i
|
i
iv
|
4
|
|
1/75/A or 2/75/A
3/77
|
iv
iv
|
|
|
|
|
|
|
5
|
USA
There are currently no national rules which regulate the requirements either
of contract fabrics or the furniture they cover. Instead, regulation is left
to local fire officers or building code officials who most often follow one
of a number of different models.
California Technical Bulletins (TB)
The State of California is one of the few states to regulate seating products
through both mandatory and voluntary requirements.
TB 117 Section E
TB 117 is a mandatory requirement for components of upholstered furniture and
Section E looks at a fabric's resistance to a small flame. Fabric mounted at
a 45o angle is exposed to a 5/8" (1.6cm) butane flame for 1 second. A
pass is achieved if the fabric does not ignite or if the time of average
flame spread is 3.5 seconds or longer for a 5" length. Virtually all
upholstered fabrics pass this test.
TB 116
This is a voluntary cigarette ignition test for completed items of furniture
(or mock ups which simulate a given furniture design) rather than individual
fabrics. It requires that lighted cigarettes are placed on all horizontal
surfaces which could conceivably support a dropped cigarette - on cushions,
arms, base, etc. Three cigarettes are placed in each area, no closer than six
inches apart, and a 6" x 6" piece of white cotton or
cotton/polyester sheeting fabric is used to cover each cigarette.
A fail is recorded if obvious flaming occurs or if a char develops more
than 2" long in any direction from the cigarette.
TB 133
This is another test for completed items of furniture intended for use in
"high risk" occupancies - including hospitals, nursing homes,
prisons, public areas of hotels, etc. In California it is a mandatory
standard in these kinds of occupancy, although there is relaxation of the
requirements in areas with sprinklers. The City of Boston has also adopted TB
133, but here it is specified for all non domestic properties and provision
of sprinkler systems is not taken into account. The test is very stringent
with rigorous pass/fail criteria. It consists of exposing a piece of
upholstered furniture to an open flame in a standard room.
The ignition source is a square gas burner placed in the furniture seat,
2" from the back and 1" above the base. The flame exposure time is
80 seconds.
The pass/fail criteria are given below. "Criteria A" were the
original parameters and are still acceptable, although "Criteria B"
are currently preferred.
Criteria A - A failure is recorded if any of the following occur:-
(
i) The temperature measured at the ceiling thermocouple increases by 200oF
or more above ambient
(ii) The temperature, measured at the 4ft thermocouple, increases by 50oF or
more.
(iii) Greater than 75% opacity at the 4ft smoke opacity monitor
(iv) CO concentration of 1000ppm or more for 5 minutes
(v) Chair weight loss of 3lbs or more during the first 5 minutes.
Criteria B
(i) Maximum heat release of 80kw or greater
(ii) Total heat release of 25MJ or greater in the first 10 minutes
(iii) Greater than 75% opacity
(iv) CO concentration of 1000ppm or greater
Boston Fire Department
Boston adopted California TB 133 in 1995 which virtually eliminated their
previous "Boston Fire Test".
The old Boston Fire Code regulated both the flammability of the chair
(using a full-scale chair test with a paper bag filled with newspaper as the
ignition source) and of component materials, including upholstery fabrics.
The fabric test (BFD 1X-1) was a vertical open-flame test using a propane
flame applied to the specimen for 10 seconds. Afterflame, afterglow and char
length were measured.
New York / New Jersey Port Authority Test
Again, California TB 133 is currently in force for all chairs going into its
buildings, but there is also an upholstery fabric requirement for a vertical
open flame test.
The fabric specimen is suspended vertically and subjected to a 1.5"
methane flame for 12 seconds. Afterflame, drip burn and char length are
monitored.
Afterflame: max average 15
seconds Drip burn: max average 8 seconds
Char length: max average 8 inches
"Steiner" Tunnel Test - ASTM E-84 T
his test is best used to assess the flammability characteristics of
composites - (ie. upholstered panels) - although panel fabric is more often
tested by itself. It is a ceiling fire simulation carried out in a 25 feet
long and 2 feet wide enclosure - the "tunnel". Test materials are
suspended on the tunnel ceiling and subjected to a 4.5 ft long flame for 10
minutes. The rate at which the flame advances is measured and used to produce
a calculated value known as the "Flame Spread Index". At the same
time, the opacity of the smoke exiting the chamber is monitored to calculate
the "Smoke Developed Index". These two indices are then used by
building code officials to classify materials into usage categories.
N.B. The test procedure itself describes neither a classification system
nor pass/fail criteria.
The most common classification categories come from the National Fire
Protection Association 101 Life Safety Code. There are different requirements
for panels listed with Underwriters Laboratories and yet further differences
for panels sold to the US government (GSA - General Services Administration).
|
|
Life Safety Code
|
U.L.
|
GSA
|
|
|
Class A
|
Class B
|
Class C
|
|
|
|
Flame Spread
|
25 max
|
75 max
|
200 max
|
200 max
|
25 max
|
|
Smoke Developed
|
450 max
|
200 max
|
450 max
|
In general, panel products are expected to meet Class A requirements,
though some occupancies have more relaxed standards.
|